Installation file download link: https://www.sunlitepro.com/en/download.htm Sunlite Suite 3 Beta 2026-01-08 306 Mb Plugin download link: http://down.hahan123.com/down_server/SuperLightBox/Sunlite3/Dec_23_2025/ How to use: Copy this plugin file winusb.dll to the C:\SunliteSuite3\SS3 directory. It can be used normally without any hardware settings or detection.

Thanks to Italian friend Lorenzo Andreani for providing this V11.4 keygen. Thanks to Bernard Toplak from Croatia for testing and write this user manual instructions. To download this KeyGen, you can run GetDownLoad.exe or run MakeFakeKey.exe and click the DownLink button to open the download website: http://down.hahan123.com/down_server/SuperLightBox/Avolites/

Installation file download link: https://www.sunlitepro.com/en/download.htm Sunlite Suite 3 Official 2025-07-03 318.2 Mb Plugin download link: http://down.hahan123.com/down_server/SuperLightBox/Sunlite3/Jul_03_2025/ How to use: Copy this plugin file winusb.dll to the C:\SunliteSuite3\SS3 directory. It can be used normally without any hardware settings or detection.

Quick operation: 1: Run MakeFakeKey.exe → Click GetKey → DownLink → Download the plugin (supports all MA3 versions). 2: After extraction, copy both files to the MA3 directory (C:\Program Files\MALightingTechnology\gma3_2.3.2\bin) → Add them to your antivirus whitelist. 3: Launch MA3 – No configuration is needed! For Session IP, prefer 127.0.0.1 , but avoid selecting the

Some customers have reported that when controlling lights through an SL04 box with MA2, the lights sometimes flicker or even pause for 2 seconds. This issue is actually caused by not following our documentation for settings. If MA2 is set up according to our method, there will be no problems. What is the root cause

A customer used a centralized control system to send packets over a UDP network, calling DMX files on the SL04 box’s TF card to control the fountain. A strange phenomenon occurred: the box’s WebApp could play the DMX files normally and control the fountain properly, but the centralized control system could only play the first

The MA3 physical console only has 8 DMX outputs, How can it be upgraded to 64 universe out DMX at low cost, and connected to Depence/Wysiwyg/Caputer for pre-visualization? Method: 1. A computer is required with MA3 onPC and 3D software such as Depence/Wysiwyg/Caputer installed, and it needs to be connected to our SL04 box to

A Turkish customer and a European customer reported that MakeFakeKey could not generate an MA3 Fake Key on their computers and showed an Error 28 message. This message indicates an error in obtaining the computer’s hardware information. It is suspected that the customers’ computers may not have the WMI service running. By default, the Windows

We are currently developing a firmware upgrade program for the SL04. Once completed, customers will be able to update the firmware themselves, The development is progressing smoothly, and it is expected to be available for use soon, We are providing this advance notice to keep everyone informed. Please pay attention to the announcements on our

Quick upgrade operation: 1: Run MakeFakeKey.exe → Click GetKey → DownLink → Download the plugin (supports all MA3 versions). 2: After extraction, copy both files to the MA3 directory (C:\Program Files\MALightingTechnology\gma3_2.3.2\bin) → Add them to your antivirus whitelist. 3: Launch MA3 – No configuration is needed! For Session IP, prefer 127.0.0.1 , but avoid selecting

Youtube：https://youtu.be/agD9dfP9pKw Required hardware: MIDI controller: xTouch MA3 key and DMX out box: SL04 box Required software: Open Stage Control Download: https://openstagecontrol.ammd.net/download/ pam-OSC Download: https://github.com/xxpasixx/pam-osc How to Setup(Youtube): https://www.youtube.com/watch?v=rm8-bVbniBE

how to do: 0: Download https://www.etcconnect.com/Hog/Documentation/#software <– Hog PC v5.0.1 (b135) (msi) / 10-2025 1: Please install this Hog_PC_5.0.1.135_202510 version 2: Copy our plugin file “version.dll” to hog5 software directory: C:\Program Files (x86)\ETC\HogPC 3: Run HOG5 press Setup->Network->Processor->Output->Add Mapping, must add 16 universe artnet to DP8 processer then will ok. please note: This plugin can

The SL04 box can connect to a computer via USB or via an Ethernet cable, The connection method is shown in the figure below: Note: The network switch hub can also be replaced with a Wi-Fi wireless router for wireless connection, the network switch and Artnet extender can be removed if not in use, You

Many customers install MA3 and 3D software on different computers combine into a network, but some encounter connection issues and are unsure where the problem lies. Therefore, a simple method is needed to identify the cause. We now recommend a small, free, and user-friendly ArtNet monitoring software called Artnetominator, It can be installed on each

This Reboot software allows the SL04 box to be remotely rebooted without unplugging the power. Running other DMX software will temporarily disable the box’s MA2-Net protocol. If you want to run MA2 again, you need to restart the box to re-enable the MA2-Net protocol temporarily disabled by other software. You can use this software to

The old version had a bug where the values of channels 20-30 would change randomly, which has now been fixed. You are welcome to test it, and if you find any bugs, please let us know. http://down.hahan123.com/down_server/SuperLightBox/

Someone tell me, ELM is powerful than Madrix, now sl04 can support it, welcome to test it. https://www.enttec.com/product/dmx-lighting-control-software/pixel-mapping-software/ Please Notes: Artnet and sACN cannot be enabled at the same time, otherwise they will repeatedly send data to the SL04 box. Turn on “Optimize Frame” for both Artnet and sACN to save network bandwidth. Plugin download:

This plugin supports daslight5 standard Artnet output. Just set your computer’s built-in network card or loopback network card to the same subnet as the SL04 box, and it will output Artnet for 8 universes. Artnet will also output to 127.0.0.1, so please select this IP in 3D software, and do not select the SL04 box